Paddlesport Accessories
PatchNRepair Emergency Repair Kit
$45.95 CAD
– Sold OutPatchNRepair Emergency Repair Kits include everything you need to field repair your equipment no matter how far from civilization you may be. These kits utilize the same water-activated MRE heater...
PatchNRepair Rugged Repair Patch - 3 x 10"
$25.95 CAD
– Sold Out-
Fixes Breaks, Cracks, and Holes & Tough Against Impact and Abrasion.
PatchNRepair is easy to use and repairs almost any hard, non-porous surface. When you heat the patch it changes from rigid to formable. The high performance self-adhesive backing holds tight against water, weather, and vibration.
Adheres to:
- Aluminum
- Plastic
- Harwood
- Metal
- Fiberglass
- and more!
***Patches sold individually*** - 1. Heat the patch to approximately 194 °F (90 °C) using an appropriate heating method. Heating methods can be MRE heater (included with kits), oven, not used for food due to possible out gassing, wrapped in foil to protect paper backing, or heat gun. When using a heat gun, do not place the heat gun too close to the patch surface or hold heat in one place for more than a few seconds. Warning: DO NOT HEAT ABOVE 270 °F (132 °C). Be sure your heating method complies with safety standards according to the conditions under which you will be applying the patch– for example, outdoors, in rainy weather, near flammable materials, etc.
2. Once the temperature is near or above 194 °F (90 °C), the material will soften and become very flexible. While heated, the patch can easily be cut to shape with scissors. Be sure to leave at least 1 inch of material on all sides of a hole or crack to improve adhesion and structural results. While wearing gloves that protect against the heat, remove and discard the film backing from the patch. Avoid touching the adhesive once the film backing is removed.
3. Press from one end of the patch to the other, applying pressure to shape it and press it into the contours of the repair surface. Continue pressing and shaping until it cools and becomes rigid again. Cooling time depends on the temperature of the damaged surface and on ambient air temperature, but normally the patch cools and becomes rigid again within one to two minutes.
Note: Do not heat with a direct flame or contact the patch directly with a heating surface that is over 270 °F (132 °C). Do not store in direct sunlight. Not for use on pressurized tanks or lines. Avoid contact of the adhesive with skin. Removal may damage painted and gel-coated surfaces. Not warranted for any specific application. -
PatchNRepair Rugged Repair Patch - 4 x 6"
$19.95 CAD
-
Fixes Breaks, Cracks, and Holes & Tough Against Impact and Abrasion.
PatchNRepair is easy to use and repairs almost any hard, non-porous surface. When you heat the patch it changes from rigid to formable. The high performance self-adhesive backing holds tight against water, weather, and vibration.
Adheres to:
- Aluminum
- Plastic
- Harwood
- Metal
- Fiberglass
- and more!
***Patches sold individually*** - 1. Heat the patch to approximately 194 °F (90 °C) using an appropriate heating method. Heating methods can be MRE heater (included with kits), oven, not used for food due to possible out gassing, wrapped in foil to protect paper backing, or heat gun. When using a heat gun, do not place the heat gun too close to the patch surface or hold heat in one place for more than a few seconds. Warning: DO NOT HEAT ABOVE 270 °F (132 °C). Be sure your heating method complies with safety standards according to the conditions under which you will be applying the patch– for example, outdoors, in rainy weather, near flammable materials, etc.
2. Once the temperature is near or above 194 °F (90 °C), the material will soften and become very flexible. While heated, the patch can easily be cut to shape with scissors. Be sure to leave at least 1 inch of material on all sides of a hole or crack to improve adhesion and structural results. While wearing gloves that protect against the heat, remove and discard the film backing from the patch. Avoid touching the adhesive once the film backing is removed.
3. Press from one end of the patch to the other, applying pressure to shape it and press it into the contours of the repair surface. Continue pressing and shaping until it cools and becomes rigid again. Cooling time depends on the temperature of the damaged surface and on ambient air temperature, but normally the patch cools and becomes rigid again within one to two minutes.
Note: Do not heat with a direct flame or contact the patch directly with a heating surface that is over 270 °F (132 °C). Do not store in direct sunlight. Not for use on pressurized tanks or lines. Avoid contact of the adhesive with skin. Removal may damage painted and gel-coated surfaces. Not warranted for any specific application. -
PatchNRepair Rugged Repair Patch - 5 x 8"
$25.95 CAD
– Sold Out-
Fixes Breaks, Cracks, and Holes & Tough Against Impact and Abrasion.
PatchNRepair is easy to use and repairs almost any hard, non-porous surface. When you heat the patch it changes from rigid to formable. The high performance self-adhesive backing holds tight against water, weather, and vibration.
Adheres to:
- Aluminum
- Plastic
- Harwood
- Metal
- Fiberglass
- and more!
***Patches sold individually*** - 1. Heat the patch to approximately 194 °F (90 °C) using an appropriate heating method. Heating methods can be MRE heater (included with kits), oven, not used for food due to possible out gassing, wrapped in foil to protect paper backing, or heat gun. When using a heat gun, do not place the heat gun too close to the patch surface or hold heat in one place for more than a few seconds. Warning: DO NOT HEAT ABOVE 270 °F (132 °C). Be sure your heating method complies with safety standards according to the conditions under which you will be applying the patch– for example, outdoors, in rainy weather, near flammable materials, etc.
2. Once the temperature is near or above 194 °F (90 °C), the material will soften and become very flexible. While heated, the patch can easily be cut to shape with scissors. Be sure to leave at least 1 inch of material on all sides of a hole or crack to improve adhesion and structural results. While wearing gloves that protect against the heat, remove and discard the film backing from the patch. Avoid touching the adhesive once the film backing is removed.
3. Press from one end of the patch to the other, applying pressure to shape it and press it into the contours of the repair surface. Continue pressing and shaping until it cools and becomes rigid again. Cooling time depends on the temperature of the damaged surface and on ambient air temperature, but normally the patch cools and becomes rigid again within one to two minutes.
Note: Do not heat with a direct flame or contact the patch directly with a heating surface that is over 270 °F (132 °C). Do not store in direct sunlight. Not for use on pressurized tanks or lines. Avoid contact of the adhesive with skin. Removal may damage painted and gel-coated surfaces. Not warranted for any specific application. -
Perception Paddle & Rod Leash
$36.95 CAD
Securely tethers your paddle, fishing rod or other accessories for a worry-free trip on the water Conveniently clips to your PFD, kayak or SUP to keep items close at hand...
Perception Scupper Plugs 4pk
$24.95 CAD
Scupper Plugs are an essential item for any kayaker who wants to enjoy the benefits of their sit-on-top kayak all year long, enabling more comfortable cold weather paddling or for...
Salus Kong Paddle Biner
$24.95 CAD
Bent Gate Large wire-gate carabiner with huge gate clearance to accommodate standard diameter paddle shafts. Ideal carabiner for river rescue, equipment retrieval, deck storage or as part of a paddle...
Salus Pig Tail Bungee Tow Line
$34.95 CAD
– Sold OutPT-440 (Yellow) With a universal fit for all QR-belts, the Salus Pig Tail extends from 26 to 44 inches. The tow system is fitted with a 2” stainless steel O-ring...
Salus Quick Release Belt
$38.95 CAD
2" wide rescue belt features a quick release cam buckle and stainless steel tri-glide. Attachment buckle for most rescue PFD’s.
Silva 58 Kayak Compass
$119.95 CAD
-
There is no better choice for serious kayak paddlers. The rubber straps with clips attach easily to the deck lines, without any need to drill in the deck. The possibility to locate the compass right in front of you makes it easy to read without letting go of the paddle ~ and you don’t need to drop your gaze from the horizon when checking your course.
The compass is waterproof and has a scratch resistant glass so that it can endure even the toughest conditions.
-
- Accuracy: ± 1° (17.8 mils)
- Apparent card diameter: 55mm
- Built-in compensator: No
- Card type: Cone
- Compatibility: Kayaks
- Dimensions: 85x55x72mm
- Gimballed cradle: No
- Heeling angle: Roll: 20° Pitch: 20°
- Heeling angle scale: No
- Illumination: No
- Lubber lines: Centre
- Material: ABS, Acrylic
- Memory ring: No
- Mounting: Rubber straps
- Mounting angle: -10° to +10°
- Protective cover: No
- Temperature operating range: -10°C to +70°C
- Type of compass: Steering compass
- Variant: Magnetic South, Magnetic North
- Water resistance: Waterproof
- Weight: 115g
- Accuracy: ± 1° (17.8 mils)
Silva 70P Small Boat Compass
$149.95 CAD
– Sold Out-
70P is a bulkhead mount compass designed for yachtsmen that demand absolute accuracy and a steady card in all conditions.
The compass handles unlimited slope of the keel line and a 30º heeling angle. The curved lubber line enables swift and clear reading at a glance without parallax errors. With a main steering scale on the horizontal part and direct reading on the vertical edge,
70P is ideal for boats with a sitting as well as a standing helmsman. It can be mounted at most angles and its compact size (70 mm) makes it suitable for smaller boats.
-
- DOUBLE SCALES: Can be read from front and above
- Accuracy: +/- 17.8mils/1°
- Apparent card diameter: 70mm
- Built-in compensator: Optional
- Card type: Cone
- Compatibility: Kayaks, powerboats, sailboats
- Heeling Angle: Roll: 30° Pitch: 30°
- Illumination: Optional
- Lubber lines: Centre
- Materials: Acrylic, PC/ABS
- Mounting: Bulkhead
- Mounting angle: +10° to +100
- Sapphire jewel bearing for friction-free movement of the compass needle: Yes
- Size: 95x72 mm
- Temperature operating range: -10 to +70 °C
- Variant: Magnetic North
- Water resistant: Yes
- Weight: 344g
Smiley's Nose Plug
$14.95 CAD
Worn and tested by some of the best paddlers in the world, Smiley's Nose Plugs stay on in the largest of holes. Very discrete and light, made with soft cushioned...
Tulita Outdoors Boat Cart
$129.95 CAD
Durable, folding, collapsible boat cart by Tulita Outdoors Suitable for canoes and kayaks Aluminum Alloy bars Soft rubber contact points for the boat 22" diameter wheels Soft plastic "tire" section...
Tulita Outdoors Foam Kayak Paddle Float
$34.99 CAD
– Sold Out- With the Tulita Outdoors Foam Paddle Float, your paddle is turned into an outrigger to stabilize your kayak while re-entering the boat from the water. The foam construction requires no inflation offering fast deployment. A durable Nylon material protects the float, while integrated whistle buckles and reflective details add to the safety of this essential piece of touring kayak safety gear.
-
- Foam base doesn't require inflation
- Durable Nylon outer
- Integrated whistles
- Reflective details
- Easily attaches to the deck of your kayak
- Foam base doesn't require inflation
Tulita Outdoors Inflatable Kayak Paddle Float
$34.99 CAD
– Sold Out- This paddlefloat has high volume and once inflated, supplies plenty of buoyancy for solid support during an outrigger self-rescue. The twin air chambers are entirely separate, with separate inflation valves and hoses, ensuring that puncture or failure of one chamber does not prevent you from inflating the other.
-
- Vinyl-coated polyester.
- Quick-release buckle for easy attachment to paddle.
- Easy-to-operate twist-turn valves on the inflation hoses.
- Integrated whistle on buckle
- Vinyl-coated polyester.
Tulita Outdoors Kayak Paddle Leash
$19.95 CAD
This coiled Paddle Leash will keep you from losing your paddle during high winds, rough seas, or fast currents. Adjustable velcro attachment loop to secure around the shaft of the...
Tulita Outdoors Universal Scupper Plug - 2 pack
$9.99 CAD $13.95 CAD
Is water coming through your scupper holes dampening your mood? Try these Sunrise Kayak Scupper Plugs! These universal scupper plugs fit a variety of brands and feature a tiered design...
Wilderness Systems Heavy Duty Kayak Cart with Beach Wheels
$339.95 CAD
– Sold Out-
Paddling Magazine’s Winner in the “Best Transport/Storage/Launching’ category for 2018, the Wilderness Systems Heavy Kayak Cart can handle big loads and is well-suited to moving fishing kayaks and angler gear.
-
- Engineered to transport the heaviest kayaks – up to 330 pounds
- Large balloon style beach wheels never go flat and easily roll over sand
- Bunker bar frame
- Adjustable width prevents the kayak from twisting and slipping sideways
- two height options – high for odd shaped hulls that would usually rub on cart wheels, low for a lower center of gravity to prevent tip overs.
- no scupper posts prevent damage to the scupper holes of the kayak
- constructed of marine-grade, high-strength, heat-treated aluminum
- alloy for superior strength
- Adjustable width prevents the kayak from twisting and slipping sideways
- Two security straps included to prevent the kayak from slipping
- Easy to load and unload the kayak – no kickstands or scupper posts required
- Collapsible and wheels can be removed for storage
- All-terrain, no-flat wheels (sold separately) will fit on same frame
- cart carrying capacity is increased to 450 lbs with no-flat wheels installed
- Engineered to transport the heaviest kayaks – up to 330 pounds
Wilderness Systems Heavy Duty Kayak Cart with No-Flat Wheels
$299.95 CAD
-
Paddling Magazine's Winner in the “Best Transport/Storage/Launching’ category for 2018, the Wilderness Systems Heavy Kayak Cart can handle big loads and is well-suited to moving fishing kayaks and angler gear.
-
- Engineered to transport the heaviest kayaks – up to 450 pounds
- Large 12” diameter airless wheels never go flat and roll over rough terrain smoothly
- Bunker bar frame
- Adjustable width prevents the kayak from twisting and slipping sideways
- Two height options – high for odd shaped hulls that would usually rub on cart wheels, low for a lower center of gravity to prevent tip overs.
- No scupper posts prevent damage to the scupper holes of the kayak
- Constructed of marine-grade, high-strength, heat-treated aluminum alloy for superior strength
- Two included security straps prevent the kayak from slipping
- Easy to load and unload the kayak – no kickstands or scupper posts required
- Collapsible and storable within large kayak hatches
- Engineered to transport the heaviest kayaks – up to 450 pounds
Wilderness Systems Rudder Kit XL Solo
$499.95 CAD
– Sold Out-
The Wilderness Systems Rudder Kit helps you gain control and efficiency in wind or fast current. The rudder blade has a foil-shape for more efficiency and less drag in the water. The Wilderness Systems Rudder Kit is the factory rudder for Wilderness Systems kayaks. This kit includes all the necessary parts, hardware, and instructions to install a rudder on your boat. For use on Wilderness Systems tandem kayaks, you will also need the Wilderness Systems Tandem Rudder Kit Module.
-
- Gain control and efficiency in wind or fast current
- Rudder kit fits all solo Wilderness System kayaks
- Can install on sit on top and sit inside kayaks